Tuesday, March 3, 2009

CSM module and a 7613 woes...or fun it depends

So i tried to bring a csm/csg module up on another chassis. All modules, including the Supervisor Engine (if you have redundant Supervisor Engines),
support online insertion and removal (OIR). You can add, replace, or remove modules without interrupting the system power or causing other software
or interfaces to shut down. So no worries there. the colors changed as expected on the LED....then went off........

SUP1234#sh module 13
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
13 4 Content Services Gateway WS-SVC-CSG-1 SAD094906MP

Mod MAC addresses Hw Fw Sw Status
--- ---------------------------------- ------ ------------ ------------ -------
13 0013.c39f.1270 to 0013.c39f.1277 1.5 Unknown Unknown PwrDown

Mod Online Diag Status
---- -------------------
13 Not Applicable


so from the above we can tell there's a problem. Hopefully not too serious.

SUP1234#hw-module module 13 reset
Proceed with reload of module?[confirm]
% module 13 is operationally off (Module Failed SCP dnld)

I only ever had this SCP dnld issue with MWAMS never a CSG/CSM module. I cant even trace back to a bug showing this as a problem...YET.
I tried to power it up manually:

SUP1234#conf t
Enter configuration commands, one per line. End with CNTL/Z.
SUP1234(config)#power enable module 13

still not shows up as failed SCP dnld....
so resetting the module with hw-module module 13 reset and power enable module 13 both fail to power up my module.
If this were an MWAM i'd assume something buggy, but this is a new module, granted the hardware is a bit newer than the other csg's..

Mod MAC addresses Hw Fw Sw Status
--- ---------------------------------- ------ ------------ ------------ -------
1 000f.342c.5318 to 000f.342c.531f 1.4 3.1(3)C7(7) Ok
2 0011.93b4.5698 to 0011.93b4.569f 1.4 3.1(3)C7(7) Ok
3 0011.5c81.1e6c to 0011.5c81.1e9b 6.1 6.3(1) 8.5(0.46)RFW Ok
4 0011.5c81.157c to 0011.5c81.15ab 6.1 6.3(1) 8.5(0.46)RFW Ok
5 0001.c9dd.0f5e to 0001.c9dd.0f65 1.4 3.1(3)C7(7) Ok
6 0002.fcc1.f844 to 0002.fcc1.f84b 1.4 3.1(3)C7(7) Ok
7 0016.46f9.0c58 to 0016.46f9.0c5b 5.3 8.4(2) 12.2(18)SXF7 Ok
8 0016.c85e.a958 to 0016.c85e.a95b 5.3 8.4(2) 12.2(18)SXF7 Ok
9 0001.c9de.32a0 to 0001.c9de.32a7 1.7 3.1(8) Ok
10 001b.53bc.b038 to 001b.53bc.b03f 6.1 7.2(1) 2.1(3.0) Ok
11 0011.92b7.c748 to 0011.92b7.c74f 4.0 7.2(1) 2.1(3.0) Ok
12 001d.70c4.fc14 to 001d.70c4.fc43 3.0 12.2(18r)S1 12.2(18)SXF7 Ok
13 0013.c39f.1270 to 0013.c39f.1277 1.5 Unknown Unknown PwrDown

so check power:
I have enough power....and its the only one not working....Im out of slots on the chassis so I can't move it around....grrrr.....
I'll move it to a different chassis and see....maybe the module got 'corrupt' while being moved from one chassis to another ( i had it somewhere else before) and wanted to spice up my afternoon.

anyone have a clue on this one? id be interested.

RS blueprint

looking at the Expanded blueprint by IE , I think I understand why multicast is such a pain, I missed out on key areas.....Im re-doing/ re-reading most of th ematerial again.

I could sit for the written any time now but until Im pretty sure of the lab payments there's no need to rush it for now, it how ever means I start preparing for the lab and ensuring nothing gets forgotten.

I have recently renewed two professional certs and while that doesn;t guarantee my written pass all the reading i did after that should get me one...or very very close (its still an exam so I'll keep my fingers crossed:)

Friday, February 27, 2009

what was cooking today:

after the csg/ggsn exploits, the better part of my week is freed up. I like it when I do something and the impact is felt almost immediately by customers, the feedback is quite refreshing.

An assesor lab some time back showed me weak on IPv6, multicast and i need to polih up on L2 technologies.

Either way I think Im still on track for the CCIE. time to start redirecting my finances towards this goal. This is probably going to be the most painful one since money is hard to come by.

anyway,,...I was on the following links today for other reasons mainly work related, and since its slowly becoming clear that data center networking might be my next bread and butter:-)

**Yes I had nowhere to book mark the pages and needed a quick reference point...:-)

Configuring Enhanced Service-Aware Billing - on the ggsn ( i deal with mobility so ggsn's sgsn,s are sort of my main dish:-)
Technical Resources for the Enterprise - Cisco Design Zone
Data Center Assurance Program (DCAP) 3.0
Protocol Compliance Statements for the CSG 3.1(3)C7(1)
Cisco DCAP Data Mobility Manager (DMM) Design Guide (External)

Tuesday, February 24, 2009

CMX CSG upgrade:

Today had me doing an MOP for some upgrades. This is for a cisco CMX running on a 7613 chassis. It assumes you plug in a CSG module on slot 13 and it doesn't have the right software installed but you have it on disk0 on the supervisor.

Next I will show how to put it together with some ggsn's, configure and test billing for mobile users.


CMX1#dir
Directory of disk0:/
5 -rw- 4736628 Jun 25 2008 02:33:06 +03:00 c6csg-apc.31-3.C7.7.bin

The above shows the image we want is in disk0
Now make the file above accessible via tftp as follows:

CMX1(config)#tftp-server bootflash: c6csg-apc.31-3.C7.7.bin

Now the file above can be reached and picked via tftp by the csg. Another alternative is to use our tftp server.

CMX1#session slot 13 processor 0

The default escape character is Ctrl-^, then x.

You can also type 'exit' at the remote prompt to end the session

Trying 127.0.0.50 ... Open

wwwwwwwwwwwwwwwwwwwwwwww

www.C o n t e n t w

www.S e r v i c e s w

www.G a t e w a y w

wwwwwwwwwwwwwwwwwwwwwwww

CSG> dir

usage

upgrade slot0:|server-ip-addr filename

ping ip-addr

show ...

copy coredump tftp|rcp ip-addr filename [rcp-user]

capture [on|off]

pktlog ...

exit

CSG> upgrade slot0: c6csg-apc.31-3.C7.7.bin

Upgrading System Image 1

CSG ExImage Nov 8 2007

R/W| Reading:lam_ppc.bin..DONE Writing:lam_ppc.bin..DONE

Read 13 files in download image. (13,0,0)

Saving image state for image 1...done.

CSG> exit

Good Bye.

[Connection to 127.0.0.10 closed by foreign host]

You should get output similar to the above.

CMX1# hw-module mod 13 reset

When the module comes up sh mod should give the output almost exactly like below:

CMX1#sh mod

5 0001.c9dd.0f5e to 0001.c9dd.0f65 1.4 3.1(3)C7(7) Ok

That’s it your CSG is upgraded.

Thursday, February 19, 2009

stil on track

Ahhh Im still on track for the ccie, had an assessor lab - still need a bit of lab time- though work has really intruded on my time table. However the work has mainly been fun appart from a few 'people' related political annoyances. I have also learnt how important some politics is to get some jobs done so I won't complain much.

Im rerouting my finances to cover for the ccie. Giving it a single shot and I don't see why it should not be passable by year end.

Im done with most of the books, so labs from now on, probably upgrading some hardware (ive been at work alot lately and the current laptop can't hack more than 5 routers on dynamips). so a new one is in order (pre-exam gift):-)